Equipment · updated 2026-10
Choosing a carpet extractor: portable, truckmount, and what to buy first
Pump psi, lift, heat, tank size, hose and wand. What each number does on a real job, and what a one-van residential crew should put on the truck first.
Most extractor mistakes are made at the spec sheet, before the machine ever touches a carpet. Somebody buys on the biggest number they can find, or on the cheapest, and six months later the machine is either too much trouble to carry up stairs or too weak to finish a living room before the first area is dry. Here is how to read the numbers, and what to buy if you are a single van with a single crew.
Portable or truckmount
A truckmount lives in the van. The engine, the blower, the pump and the heat exchanger are bolted down, and you run a long hose into the house. The machine makes its own heat, runs a high-lift vacuum, and keeps going all day. The tradeoff is the size of the buy, the engine maintenance, and the fact that the hose has to reach. A portable puts everything in a box you carry in. It heats water with an internal heater or it does not heat at all, it has less lift, and the tanks are small enough that you will be walking out to dump and refill.
The honest answer for a one-van residential crew in the Valley is that it depends on your mix. If most of your work is single-story tract homes in Clovis, Fresno and Madera with the van parked in the driveway, a truckmount earns its space. If your work is apartments, second-floor units, offices and the occasional commercial restroom carpet, a good portable is faster to set up than a hose run and you will use it every day. A lot of crews end up with both: a portable for the stairs and the small jobs, and a truckmount once the volume is there.
We carry portable extractors on the equipment shelf and truckmount parts and solutions in the parts aisle. We do not keep truckmount units themselves in the building. If that is the direction you are heading, ask at the counter and we can talk through a special order.
The numbers that matter
- Pump pressure. Measured in psi at the pump. Most portables sit somewhere between about 100 and 500 psi, and the number only matters at the wand. A higher-psi pump pushes solution through a longer hose and a finer jet. For ordinary residential traffic lanes you do not need to chase it. Past a point, more pressure is a way to splash the baseboards.
- Water lift. This is the vacuum, and it is the number that decides how dry the carpet is when you leave. Lift is measured in inches of water, and the spec to look at is lift at the wand with the hose attached, not the free-air number printed on the box. Dry time is where callbacks start, especially in a wet tule fog week when nothing dries on its own.
- Heat. Hot water loosens soil and lets you run a leaner chemical mix. Many portables have an internal heater, and the ones that do not rely on you filling with hot water from the customer’s tap. If you work in cold months, an inline heater is not a luxury. In July in Fresno the tap water coming out of an outdoor spigot is already warm enough that you may never notice.
- Tank size. The solution tank and the recovery tank are separate numbers, and the smaller of the two sets your pace. Six gallons of solution is not much if the recovery tank is also six, because you will be dumping every couple of rooms. Look for a recovery tank that is easy to empty at the curb without lifting the machine to your shoulder.
- Weight and wheels. If you are carrying it up stairs, weigh it empty and think about how it is when it is full. Big pneumatic wheels beat small plastic ones on thick pile and gravel driveways.
- Hose and wand. A two-inch vacuum hose moves more air than a one-and-a-half, so lift survives a longer run. A wand with a decent jet and a clear head lets you see the soil leaving. A lighter wand saves your wrist across a day of forty strokes per room.
Hose, wand and jets
The part of the extractor you will replace most is the part nobody photographs for the ad. The solution hose, the vacuum hose, the wand valve and the jets get stepped on, kinked, dragged through gravel and clogged with hard water scale. Valley water is hard, and a clogged jet shows up as a stripe in the carpet where the spray is not reaching. A wand with a six-inch pass and three jets that are two thirds clogged makes a pass that looks like a comb.
When you shop for a machine, look at how many spare parts the line has on the shelf. A machine you love that has no wand parts available is a machine that sits in the shop. Our parts aisle has wands, vacuum hose, solution hose, jets, fittings, check valves, filters and chemical pumps, and the product pages tell you which machines they fit.
What a one-van residential crew should buy first
Think about the first four weeks, not the first four years. You need a machine that finishes the carpet dry, a way to pre-treat, a way to spot, and spares for the things that will fail on a job in a customer’s living room.
- One portable extractor with a heater, a recovery tank you can empty in one hand, and a real wand. If you have a choice between a heavier machine with more lift and a lighter one with less, take the lift unless you are working stairs every day.
- Forty feet of vacuum hose and forty of solution hose, as a set, rather than two short ones joined together. Fewer joints, fewer leaks.
- A spare wand valve, a spare set of jets, and a spare solution hose. The first one to fail is the one you do not have.
- A pump-up sprayer for pre-spray, and a second one for rinse so the two never get mixed in the same tank.
- A small rotary machine or a carpet brush once you start on the heavy traffic lanes. Agitation is half of cleaning.
- A defoamer, because every extractor produces foam sooner or later and a foamed-up recovery tank can pull foam into the vacuum motor.
A second extractor is the right second purchase. A crew with one machine and no backup loses an entire day when something fails. A crew with a spare loses an hour.
Wear parts to stock
Keep these on the truck, not in the shop. When the part you need is thirty minutes away, you lose a job.
- Jets, in the size your wand uses, plus the little washers and O-rings that seat them.
- Wand valve repair parts and an extra valve body if the line supports it.
- A solution filter, and the strainer that sits in front of the pump.
- Vacuum hose cuffs and a roll of tape that actually sticks to wet vinyl. Hose cuffs split first.
- A check valve for the solution line. When one fails the machine pulls air and the pump runs dry.
- Vacuum motor brushes if the machine uses them, and a spare recovery tank lid gasket. A lid that does not seal turns the machine into a very expensive fan.
- Descaler. Hard water builds up inside the heater and the lines. A scheduled flush costs less than a service call. Truckmount crews can pick up the coil solution and neutralizer in the parts aisle.
Care that makes the machine last
Flush the machine with clean water after every job. Pull the filters and rinse them. Open the recovery tank and leave the lid off overnight so it does not sour. If the machine heats, run vinegar-based or manufacturer-approved descaler through it on a schedule you keep on the wall of the shop, not in your head. Replace the vacuum hose before it fails, not after.
If you are not sure which way to go, the equipment shelf has portables set up where you can look at them, and the counter can show you how the wand comes apart. Bring your own hose measurements if you are replacing a machine. Delivery on the route is free over the minimum, so spares do not need a special trip.