Order by 11:00 and it rides today's truck · Fresno & Clovis dailyCounter open · 5889 E Clinton AveTeam login
MARCOINDUSTRY SUPPLIES · FRESNO

Hard Surface & Floor Care · updated 2026-10

A floor care schedule for a school or office: daily to annual

What to do each day, week, month and year on VCT, sealed concrete and tile, what the pad colors mean, scrub and recoat or strip, and how to plan the summer.

A floor that looks good in October was planned in August. Floors in schools and offices do not fail because somebody forgot to mop. They fail because the finish wore through in the traffic lanes in the spring, nobody noticed, and by the time they did the only fix was a full strip. A schedule that you actually keep gets you to the next summer with a floor you do not have to rescue.

This guide assumes a building with a mix of vinyl composition tile (VCT), sealed concrete and ceramic tile, such as an elementary school, a church, a small office, or a clinic. The same bones work for most small commercial buildings.

Daily

Daily work is mostly about keeping grit off the floor, because grit is what wears the finish.

  • Dust mop or microfiber mop every hard surface. In the Valley, dust comes in on shoes from harvest, field edges, and the dry months, and it acts like sandpaper on the finish.
  • Spot clean spills the moment they happen, especially sugary ones like juice and soda, which are sticky and track.
  • Damp mop with a neutral cleaner. Use the dilution on the label. Too strong a mix leaves a residue that dulls the floor and makes it tacky.
  • Walk-off mats at every entrance. The most effective floor care product in the building is a mat that catches grit at the door.
  • Clean restroom tile and grout with a tile and grout cleaner and a deck brush where the grout is dirty.

Weekly

  • Autoscrub or scrub the high-traffic lanes: main corridors, cafeterias, entrances, and the lobby. A scrubber with a soft pad lifts the soil that a mop pushes around.
  • Spray buff if the finish has lost its shine. A spray buff is a light burnishing pass with a spray product and a red pad. It restores gloss on worn spots without a recoat.
  • Clean walk-off mats, and vacuum entry carpet.
  • Deep clean restrooms. Floors, floor drains and grout.

Monthly

  • Machine scrub every hard floor, not only the lanes. A neutral cleaner and a blue pad on a rotary machine such as the Minuteman Front Runner, or an automatic scrubber, will remove the film that daily mopping leaves.
  • Inspect the finish. Look along the traffic lanes at a low angle, with light coming across the floor. Dull, scratched or thin areas show up. Note where it is wearing.
  • Burnish or buff with a high-speed machine if your finish is rated for it.
  • Clean the baseboards and the edges, which a machine can’t reach.

Quarterly and seasonal

  • Scrub and recoat. Scrubbing removes the top layer of dirty finish, and one or two thin coats of finish go on afterward. This renews the floor without removing the whole film.
  • Seal and polish sealed concrete if it is showing wear, and clean the grout lines of tile.
  • Check dispenser and cart stock for the summer.

Annual

  • Strip and refinish VCT and any other floor that carries a finish. This is the full reset: the old finish is removed, the floor is rinsed, and fresh coats go on.
  • Reseal concrete, if it carries a sealer, and the grout on tile.
  • Service the machines. Replace the squeegee blades, the wiper gaskets, the pad driver, the cords and the batteries.

Pad colors

Most pad makers follow a common color code, though it is worth checking the package, because brands differ a little.

  • White: polishing. Gentle, for light buffing of a finished floor.
  • Red: buffing and spray buffing. Cleans lightly and shines.
  • Blue: cleaning and scrubbing. The everyday scrub pad.
  • Green: heavier scrubbing, and a first pass on a floor with build-up.
  • Brown or black: stripping. Aggressive, for removing old finish.

Pads are on the Hard Surface aisle, along with pad drivers. The size must match the machine. A 17 inch machine uses a 17 inch pad, and a pad that is too small leaves a stripe at the edge.

Scrub and recoat or strip

This is the decision that costs or saves the most money. A rule that works: if the finish is thin or dull but still bonded, scrub and recoat. If the finish is yellowed, peeling, built up in the corners, or so thick that it has black scuffs that won’t scrub out, strip it.

A floor can take many recoats, but each one adds a layer, and a floor that has been recoated many times without a strip eventually gets cloudy and brittle. Plan on a full strip about once a year in a school and less often in a low-traffic office. Watch the floor, not the calendar.

  • Scrub and recoat: needs a neutral or light scrub cleaner, a blue pad, thin coats of finish, and drying time.
  • Strip: needs a stripper, a brown or black pad, a wet vacuum or floor extractor to pick up the slurry, a rinse, and then fresh coats of finish. The Hard Surface aisle carries strippers including an orange-based product and a no-rinse product, along with finishes and sealers.

Strippers are a chemical. Read the label and the safety data sheet, wear gloves and eye protection, and put out wet floor signs. Don’t let the stripper dry on the floor.

Planning the summer

Summer is the only time a school is empty, which is why strip and refinish work is done in June, July and August. In the Valley, summer is also hot and dry, which makes finish dry quickly and sometimes too quickly. A fast-drying coat in a hot, dry building can flash and leave streaks. Run the air conditioning, keep fans off the wet floor, and work in sections.

Plan backward from the first day of school. Work out how many rooms and hallways you have, how many you can do in a day, and when the finish must be cured. Most finishes need to dry between coats and then cure before heavy traffic or furniture goes back. The label will say when. Order the product early, because every contractor in the area is buying the same finish the same week in July.

  • Order stripper, finish, pads and sealer in June, not in the week of the job.
  • Test a small area first.
  • Move furniture in a sequence that lets you finish one room before starting the next.
  • Keep a log of what was done to each floor: date, products, number of coats.

How much finish

Coverage depends on the product, the floor porosity, and how the finish is applied, and the label is the only number that counts. The label states a coverage figure in square feet per gallon per coat. Measure the floor, divide by the label coverage, multiply by the number of coats, and add a margin for the first coat on porous floors. Be conservative. Running short in the middle of the last coat is worse than having a half-gallon left over.

Sealers on bare VCT and on concrete soak in more than finish does on a sealed floor. The counter can help you total up the product for a building if you bring the room measurements. Delivery on the route means that if you do run short, you aren’t driving across town.

More from the counter